Blog

Mini review of the Raspberry Pi Global Shutter Camera - CNX Software

CNX Software – Embedded Systems News

Reviews, tutorials and the latest news about embedded systems, IoT, open-source hardware, SBC's, microcontrollers, processors, and more Medical Endoscope Lens

Mini review of the Raspberry Pi Global Shutter Camera - CNX Software

Raspberry Pi Trading has just launched the 1.6MP Raspberry Pi Global Shutter Camera which can capture rapid motion without introducing artifacts usually experienced with rolling shutter cameras such as the earlier Raspberry Pi Camera modules, including the latest Raspberry Pi Camera Module 3.

The company sent me Raspberry Pi Global Shutter Camera sample together with a 16mm C-mount lens for review, and I’ll report my experience after going through the specifications of the new camera.

The camera ships with a 15cm ribbon cable and a screwdriver for the back focus lock screw. The Sony sensor offers high light sensitivity and can work with short exposure times as low as 30μs with adequate lighting for high-speed photography. The company says the Global Shutter Camera will remain in production until at least January 2032.

I received not one, but two packages because the Raspberry Pi Global Shutter Camera requires a separate lens.

The other side of the package has some information about the camera, and a link to a getting started guide that should work once this review is online. But I hadn’t access to it during the review, and the camera can be controlled just like any other Pi camera modules.

The Raspberry Pi Global Shutter Camera comes with a screwdriver to tighten the C-mount screw after the lens is installed.

The back of the camera is protected by a plastic cover and the flat cable is already inserted into the connector. We can also see some test point on the back of the camera.

The other package comes with a PT3611614M10MP 16 mm C-mount lens that’s not exactly new because it’s also used with the Raspberry Pi High-Quality camera.

It has a narrow field-of-view as we’ll see in the review, and features focus and aperture adjustment rings.

The first step is to screw the C-mount lens into the Global Shutter camera and secure it by tightening the back focus adjustment ring’s lock screw on the camera itself.

Since the camera comes with a mounting thread it can easily be placed on a typical tripod. We’ll also need to insert the flat cable into a Raspberry Pi SBC ‘s camera connector, prepare a microSD card with the latest Raspberry Pi OS, and connect the board to a display and power supply.

The flat cable is rather short so I use a cable tie to attach the Raspberry Pi 4 SBC to the handle of the tripod. Not neat, but that will do for the review.

I installed the latest version of Raspberry Pi OS 32-bit, but the camera was not detected at all:

I had to run the following commands to update the system with the latest libcamera2 libraries before rebooting the system:

The camera was finally detected:

I don’t expect this issue to happen after release, but if you have detection issues just make sure to update the OS. As we previously noted the 16mm C-mount lens has a narrow field of view, and it looks like it’s zooming as well, as I did not expect to only see the car at this distance. The quality looks very good though.

You can see a sample below taken with the command:

Click for the original size

For comparison I took a photo with my Canon EOS 700D DSLR camera at the same location with minimum zoom:

So the zoom level of the Raspberry Pi Global Shutter Camera with the 16mm C-mount lens is even higher than the one of my camera.

For reference, here’s some information about the image captured with the Global Shutter Camera:

So I decided to move the test subjects a bit further…

So now I can see the car and the Hotwheel thing… So let’s shoot a video to show video recording with motion using the following command:

Note the video was shot at night albeit with good lighting and it looks pretty smooth to me. It’s similar to the e-con Systems e-CAM20_CURB global shutter camera I tested on Raspberry Pi 4 last November.

Here are the details about the sample for reference:

The resolution is 640×480 with a 30 FPS framerate and 10Mbps constant bitrate.

As we previously mentioned the 16mm lens supports focus and aperture adjustments, so we demonstrate those in the video below.

The Raspberry Pi Global Shutter Camera is available now for $50 plus taxes from your favorite Raspberry Pi distributor. You’ll also need a camera lens, and the 16mm C-mount lens used in this review costs $65.99 on Amazon. If you need a wider angle, then you could get the 6mm CS-mount lens that goes for $15.99.

Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software engineering manager, and starting to write daily news, and reviews full time later in 2011.

Support CNX Software! Donate via cryptocurrencies or become a Patron on Patreon

What is the model of the display attached to Raspberry Pi? Do you have a review of it?

It’s a 10.1-inch touchscreen display from SunFounder.

Review: https://www.cnx-software.com/2021/11/19/10-1-inch-raspberry-pi-all-in-one-touchscreen-display-review-installation/

Why only 60.38 fps when the Sony sensor can go as fast as 30μs/frame? Why only 4:2:0 subsampling for JPEG? Can you save a RAW image and post the exiftool output? What’s the shutter speed for it? Why only 640×480@30 fps for video? Can’t is record HD video? Then it’s not worth $50.

Mini review of the Raspberry Pi Global Shutter Camera - CNX Software

2/3 Pinhole Lens Change Ad Consent Do not sell my data